China Netel logoChina Netel
AVAYA END-OF-SALE MODEL

Avaya 1140E IP phone

1140E (IP phone with large graphical display) is end-of-sale. We still handle spare parts, repair, maintenance contracts and replacement for it, checked against the model and part number.

Model
1140E
Part number
—
Series
IP Phones · 1600 / 1100 / 1200 Series
Product status
End-of-Sale (discontinued)

Model and part number

1140E (IP phone with large graphical display) belongs to IP Phones · 1600 / 1100 / 1200 Series and is a discrete orderable item within the Avaya portfolio. No part number is recorded for this model in our current data; we can trace it from the model name.

The same model can carry more than one part number (P/N), depending on year of manufacture, configuration or regional packaging. Please quote the part number when asking about spares or pricing; if you only have the model name, we can look the part number up for you.

ModelPart numberSeriesProduct status
1140E—IP Phones · 1600 / 1100 / 1200 SeriesEnd-of-Sale (discontinued)

Where these systems stand today

These three families span three generations of Avaya entry-level IP phones. The 1100 Series arrived around 2004 and was long the standard set on CS 1000; the 1200 Series is older, an entry line from the H.323 era; the 1600 Series speaks both H.323 and SIP and is still common in branch offices in China.

End-of-sale did not change the access protocol, so as long as the Communication Manager or IP Office release stays put these phones can keep working for a long time. The trouble sits at both ends: firmware is frozen at its last build and may not be supported on newer platforms, and accessories such as power adapters, wall-mount kits and key caps went out of supply earlier, so one missing part can take a whole set out of service.

Replacement and migration advice

For the 1600 Series the notices name the J Series, and that route still holds today: the J Series is in production and can be swapped in directly. The 1100 and 1200 Series are different — the notices state plainly that there is no direct replacement, so the model has to be chosen afresh against station count, key requirements and the platform release in use. A single "move everything to J Series" plan therefore does not fit all three families; establish which generation each phone belongs to and what platform it sits on, then build the replacement list.

SUPPORT

Four things we still handle after end-of-sale

End-of-sale does not mean the end of support. These are the four things we actually do for discontinued models, and the four questions customers ask most often.

Spare parts

We check original and refurbished stock against the part number, starting with consumables such as power supplies, handset cords, fans and boards.

Ask about parts

Repair and RMA

Board-level and unit-level repair, with fault isolation before any quote. If a unit is beyond economic repair, we say so.

Repair service

Maintenance contracts

In-service systems can be covered by a maintenance contract with remote support, on-site dispatch and spare parts cover, scoped by response level.

Maintenance plans

Replacement and migration

Replacement paths are based on interface type, port count and software release. Where a smooth transition is possible, we do not propose a rip-and-replace.

Current models
FAQ

Common questions about this model

Q: Can I still buy the 1140E? A: New units are no longer supplied. Spare parts, refurbished units and functionally compatible substitutes may still be available; we check stock against the part number and give you a definite answer. Note also that most replacement models named in an end-of-sale notice have themselves been discontinued, so confirm the current position with us before changing model.

Q: Can 1603 / 1608 / 1616 be replaced directly by the J Series? A: Yes, provided key counts and features line up. The key counts and expansion options on the J139 and J179 do not match the 1600 Series exactly, so if agents rely on fixed key positions the labels and the user training have to be redone after the swap.,Q: Can 1603 / 1608 / 1616 be replaced directly by the J Series? A: Yes, provided key counts and features line up. The key counts and expansion options on the J139 and J179 do not match the 1600 Series exactly, so if agents rely on fixed key positions the labels and the user training have to be redone after the swap.

Q: How do I find out whether spare parts still exist for my model? A: Send us the model name or part number (phone 400-678-9559, email gq.han@china-netel.com). We check stock and cross-reference alternatives first, then come back with a plan and a quote.

The model is end-of-sale, the problem is still ours to solve

Tell us the model, the part number and what the system is doing. We will tell you whether parts, repair or migration makes more sense before we talk price.

Contact Us
Call Us